splashhopper Posted December 2, 2009 Report Share Posted December 2, 2009 No matter how i try to keep that little red tube secured to the can, it disappears So now I have three cans of the stuff and no little red tubes to attach to the nozzle... Does anyone know if there are other tubes available? Or another method of spraying the stuff where I want it to go( confined space) Or another product even that has a different extended nozzle.. I am about to change the thermostat on my van and don't think it has ever been changed before,.... So I want to soak the crap out of the bolts BEFORE I try to undo them. Thanks Link to comment Share on other sites More sharing options...
ld17 Posted December 2, 2009 Report Share Posted December 2, 2009 I've seen can's of WD 40 with the red tube attached to the can. You just flip it up like a hinge and your good to go. You can't lose it cause it's attached. Also I would just use and elastic around the can and you won't lose the tube next time. Link to comment Share on other sites More sharing options...
Governator Posted December 2, 2009 Report Share Posted December 2, 2009 As LD said above: http://www.canadiantire.ca/AST/browse/4/Au...art%2BStraw.jsp Link to comment Share on other sites More sharing options...
TJQ Posted December 2, 2009 Report Share Posted December 2, 2009 I've seen can's of WD 40 with the red tube attached to the can. You just flip it up like a hinge and your good to go. You can't lose it cause it's attached. Also I would just use and elastic around the can and you won't lose the tube next time. its a fact!! lol.. oh the information stored in this community's consciousness. Link to comment Share on other sites More sharing options...
snag Posted December 2, 2009 Report Share Posted December 2, 2009 I cut the straw in half sometimes so I have 2 short ones to lose Link to comment Share on other sites More sharing options...
Twocoda Posted December 2, 2009 Report Share Posted December 2, 2009 happens all the time ...empty the contends out of the pressurized can into a spray bottle and squirt the stuff...i but the big cans ( non pressurized) and transfer it into a windex bottle...there is a "stream" setting on the bottle for the tight spots Link to comment Share on other sites More sharing options...
splashhopper Posted December 2, 2009 Author Report Share Posted December 2, 2009 I've seen can's of WD 40 with the red tube attached to the can. You just flip it up like a hinge and your good to go. You can't lose it cause it's attached. Also I would just use and elastic around the can and you won't lose the tube next time. Tried the elastics... tried tape.... still lose the darn things I sprayed the crap out of it this am... van is smoking like crazy for a few minutes burning that off... Link to comment Share on other sites More sharing options...
splashhopper Posted December 2, 2009 Author Report Share Posted December 2, 2009 happens all the time ...empty the contends out of the pressurized can into a spray bottle and squirt the stuff...i but the big cans ( non pressurized) and transfer it into a windex bottle...there is a "stream" setting on the bottle for the tight spots Princess Auto has 4 litre jugs of it on sale right now... $19.99 First time I noticed it was available in a pump format vs aerosol So, how do i get the stuff out of the pressurized can?... Just spray it? Link to comment Share on other sites More sharing options...
irishfield Posted December 2, 2009 Report Share Posted December 2, 2009 Stuff has plenty of uses... unfortunately they don't include being used as a lubricant or rust breaker. Buy the proper stuff for the job.... Link to comment Share on other sites More sharing options...
Daplumma Posted December 2, 2009 Report Share Posted December 2, 2009 PB Blaster works very well for me. Link to comment Share on other sites More sharing options...
dannyboy Posted December 2, 2009 Report Share Posted December 2, 2009 WD-40 isn't much of a penetrating oil or lubricant for that matter, buy some penetrating oil in a squeeze bottle so it will go exactly where you need it. Also use some anti-seize on the threads before you reassemble. Dan Link to comment Share on other sites More sharing options...
cuzza Posted December 2, 2009 Report Share Posted December 2, 2009 Stuff has plenty of uses... unfortunately they don't include being used as a lubricant or rust breaker. Buy the proper stuff for the job.... Too right - WD40 stands for Water Dispersant 40th attempt Canadian Tire do a WD40 pen which is useful for tight spots http://reviews.canadiantire.ca/9045/0381508P/reviews.htm Link to comment Share on other sites More sharing options...
Fish Farmer Posted December 2, 2009 Report Share Posted December 2, 2009 LOL.LOL.LOL. I looked for mine yesterday also, your not alone. I put the little red straw in a place were I would find it. NOW I can't think of the place. Link to comment Share on other sites More sharing options...
misfish Posted December 2, 2009 Report Share Posted December 2, 2009 3 in 1 oil. Link to comment Share on other sites More sharing options...
skinny Posted December 2, 2009 Report Share Posted December 2, 2009 back when i ran my shop i use to always put the tubes in the can that held the pens by the phone I think I still have a bunch let me know what you need Link to comment Share on other sites More sharing options...
BassAsin Posted December 2, 2009 Report Share Posted December 2, 2009 i'll never cheap out again, for the extra 63 cents i'll buy the one with the attached flip up straw, kinda like the one i have sitting on the coffee table in front of me right now hahaha Link to comment Share on other sites More sharing options...
vinnimon Posted December 2, 2009 Report Share Posted December 2, 2009 castle makes a fantastic product,liquid torch,spray a few times let it sit and spray again.I keep a few cans in my service vehicle,just in case my cutting torch runs dry.Ive used dozens of brands and types.wd 40 is a good cleaning agent,bicycle chains etc.But not a penetrant,maybe a temp lube. Link to comment Share on other sites More sharing options...
tjsa Posted December 2, 2009 Report Share Posted December 2, 2009 I can't find mine right now to take a picture, but you can buy from an electronics shop(ones that supplies chemical degreasers/cleaners, etc....) a complete replacement nozzle for the spray can. You take the existing nozzle that you have to insert the stupid little straw tube into off, and replace it with this unit that has the nozzle and straw attached permanently. It also has a bit of a coil in it along with a six inch straight section. That way you can depress the nozzle with one hand, and aim with the other hand, and it pulses the spray. Worked really well for my application cleaning sliding volume controls, potentiometers, etc........... Link to comment Share on other sites More sharing options...
Billy Bob Posted December 2, 2009 Report Share Posted December 2, 2009 WD-40 has severed me VERY well for over 30 years.......it has protected my firearms (19 total) for many years....every gun is wiped down with WD-40 before being put in the gun safe.....never a finger print is left on any firearm and this has been effected on every gun..........but anyways.......I use a VERY EXPENSIVE item to contain the little red tube because it's very important to my well being.......it's called a rubber band around the can.......this very expensive item holds the little red tube for many years to come.... Good Luck finding the correct size rubber band. Bob Link to comment Share on other sites More sharing options...
smally21 Posted December 3, 2009 Report Share Posted December 3, 2009 I've seen can's of WD 40 with the red tube attached to the can. You just flip it up like a hinge and your good to go. You can't lose it cause it's attached. Also I would just use and elastic around the can and you won't lose the tube next time. where am i going to find an elastic? probably next to the red tube... Link to comment Share on other sites More sharing options...
Muskieman Posted December 3, 2009 Report Share Posted December 3, 2009 (edited) Stab the top of the cans to let the pressure out and pour the contents into a spray bottle with an adjustable nozzle. Or you can usually buy a gallon of the stuff that comes with a WD-40 branded spray bottle for about 25$ or so. RFS Edit... GEEEZZZE!! I should've read with my eyes instead of the beer can...... Twocoda beat me to it. Edited December 3, 2009 by Randy from Sturgeon Link to comment Share on other sites More sharing options...
Twocoda Posted December 3, 2009 Report Share Posted December 3, 2009 Stuff has plenty of uses... unfortunately they don't include being used as a lubricant or rust breaker. Buy the proper stuff for the job.... # 1 reason for WD 40 : spray your worms with it ..to catch more fish...seriously! Link to comment Share on other sites More sharing options...
irishfield Posted December 3, 2009 Report Share Posted December 3, 2009 Like I said.. plenty of uses.. just that a lubricant isn't one of them. Drying out ignition caps... cleaning stuff like your grimmy hands.. using it as a fish attractant.... but putting a film of lubricant between moving parts.. never ! Not on anything I wanna depend on anyhow... Link to comment Share on other sites More sharing options...
SlowPoke Posted December 3, 2009 Report Share Posted December 3, 2009 PB Blaster works very well for me. I bought a case of PB from the US before it was available in Canada; still have 3 cans left and lots of straws! PB Blaster is the ULTIMATE penetrating oil. I won't waste my time with anything else. As far as I know, it is now available at Fastenal and maybe CTC but not sure. As for a spray lube, "E4 Lube" is the best I've come across and it smells nice. This is good for lubing hinges in the car and house. Good luck finding it however; I get mine from an overhead door company in Ottawa. .....never a finger print is left on any firearm and this has been effected on every gun Hmmm, good to know. Link to comment Share on other sites More sharing options...
Billy Bob Posted December 3, 2009 Report Share Posted December 3, 2009 Like I said.. plenty of uses.. just that a lubricant isn't one of them. Drying out ignition caps... cleaning stuff like your grimmy hands.. using it as a fish attractant.... but putting a film of lubricant between moving parts.. never ! Not on anything I wanna depend on anyhow... Actually it does work as a lubricant very well.....I have a Browning Sweet Sixteen (Belgium made) I purchase new in 1974 and WD-40 is the ONLY lubricant I have ever used on it.....the Browning Auto-5 is a recoil semi-automatic shotgun and depends on the properly cleaning and lubricating the magazine tube in order to eject and reload every round properly.....I leave the setting on the tube for HIGH BRASS (heavy loads) yet I can shoot very light trap loads with it without a problem...WD-40 is petroleum based but is very thin which makes it actually the BEST choice for anyone that hunts in extreme cold conditions because it will not thicken up like some other gun oils that have disappointed the hunter when he pulled the trigger and the firing pin did not strike the prime because the oil used thicken up enough to prevent the firing pin from moving......this has never happened to me because of my exclusive use of WD-40 I have a WELL lubricated rag that I saved from soooo many times of spraying it with WD-40 that is stored in the gun safe...this rag is my wipe down rag I use before putting any gun away in the safe....my safe is in the basement I don't use a de-humidifier or a golden rod in the safe.....just wipe them down and store....believe me this has been very effective for me for almost 40 years now. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now