Jump to content

Cannonball release confusion


HTHM

Recommended Posts

I was out today and having just switched to mono on my downrigging rods, I am finding that the releases on the cannonballs do not release. I was towing my catches rather than fighting my catches. I had a monster sheepshead on the line at the end of the day, ~10 pounds I estimate, and even that did not trigger the release. One will release as I am lowering the cannonball to depth, and I have to start over with the setup, like 4 times in a row. :angry: Then line further back in the clamp, and no release.

What am I doing wrong?

 

Link to comment
Share on other sites

Some releases are adjustable. I have some that have a tab that you can pull it out and tightens the release.

 

Also, if your release is too light you can loop the line around the release to make it hold better.

Edited by JohnBacon
Link to comment
Share on other sites

What Spiel said

 

I've run Offshores since the day they came out. Cut the wire leads off and replace with longer leads. I run about 18" of weed wacker line in bright green and crimp off with small wire crimps from the hardware store designed for the smallest braided outdoor wire.

 

For salmon and trout I put all lines - mono or braid right at the back. On Erie I played around with 1/2 to all the way and dint really see any difference.

 

Make sure you get some bend in the rigger rods so any hit or struggle by a hooked fish makes the rod bounce.

Link to comment
Share on other sites

There are a couple brands on the market like the Blacks or Chamberlain release http://www.downriggerrelease.com/

 

the release mechanism is adjustable by turning a knob. With a weigh scale you can set the tension for the type of fish you are targeting - say 4 lbs for walley, 8lbs for kings.

 

You can also combine this with different weight rubber bands to work with your target species

http://www.michigansportsman.com/Tips_n_Trix/rubber_band_releases.htm

 

ideally, enough resistance to load up the rod into an "n" shape, you will see a shaker swimming, (or one of those come-along walleyes) and a real fish will pop it every time.

Link to comment
Share on other sites

One thing i agree with for sure is getting a good bend in the rod, i crank the rod till im all but certain its going to pop out by itself. I can tell if a 10" shaker is on instantly.

I use the scotty rigger clips on the strong setting and bury the line in the clip every time as well.

Edited by Gallie
Link to comment
Share on other sites

Albert I've been using these for years. Knew a few Charter guys and this is all they use now, cheaper and they work great. I have about 30 around now I keep for spares. Bought a bunch from a table at the Ancaster Swap meet. You used to get them in the local tackle shops for about $2.00 No need to spend big money, I still have a few Off-Shore I use, but these work as good.

Use them Salmon and Walleye fishin. They came with a curtain ring I through away and made my own hook up swivel with split ring and big snap.

Just watch how far back you put your line. Load your rod a little lighter in you rod holder, you could be putting too much load on your releases.

Clip1_zpsimhoaujz.jpg

 

Clip2_zpskw02hndx.jpg

Edited by Fish Farmer
Link to comment
Share on other sites

Blacks releases are great been using them for many many years !!! Lots of adjustment it pays to have great releases as they are NOT all the same and yes offshore ones work great too and it's good to change the pads sometimes too there is so eh tricks to help depending on line type

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recent Topics

    Popular Topics

    Upcoming Events

    No upcoming events found

×
×
  • Create New...