skinny Posted March 4, 2010 Report Share Posted March 4, 2010 ok I was given a swede-bore auger to use it has ofset crank and fold up. first time out with it it took 2 of use just to get a hole started and cut. I talked to the guy that had it before me he did say it was a bugger to get going. I spoke to him and we decided to weld on a lag bolt for a center and start to sort of helpull the auger in. this worked until tuesday when the lug got broke off from someone twisting it sidways. anyway I know the auger should work with out the add on. i wonder if it is bent (is there a way to check) it needs the blades replaced or sharpend for that matter I'm not sure they are on correctly. any help or pictures would be great . I would like to get out one more time either tomorrow or Sat Link to comment Share on other sites More sharing options...
Guest ThisPlaceSucks Posted March 4, 2010 Report Share Posted March 4, 2010 sounds like a dull auger. Link to comment Share on other sites More sharing options...
skinny Posted March 4, 2010 Author Report Share Posted March 4, 2010 it could be that as i didn't put new blade on it or anything i may try to find a set today . wil they still be ok for next year Link to comment Share on other sites More sharing options...
splashhopper Posted March 4, 2010 Report Share Posted March 4, 2010 not an expert.... but i can tell u ... i was just given a fin bore 6 " auger... with sharp blades in it..... whoooosh unbelievable... gonna buy a set of new blades for the 8" auger that i bought this winter... should solve that issue real quick too. Link to comment Share on other sites More sharing options...
wallyboss Posted March 4, 2010 Report Share Posted March 4, 2010 Might have to do some work on where you had welded the lag bolt. All you needed was a new set of blades. One small bang on the blades and it will destroy them. You can sharpen dull blades but if the angle is gone then you need a new set of blades. Link to comment Share on other sites More sharing options...
skinny Posted March 4, 2010 Author Report Share Posted March 4, 2010 is it possible that the blade mount could be bent I have ground off the start lag now Link to comment Share on other sites More sharing options...
Sinker Posted March 4, 2010 Report Share Posted March 4, 2010 Get new blades. If you didn't mess up the angles where they mount, it will melt thru ice like nothing. You don't have to push down on an auger to cut a hole. Just turn it and it will dig in. NEVER bang it on the ice, NEVER touch the blades, and ALWAYS put the guard back on when your done cutting. I have the 8" fin bore and it will cut through 23" of solid ice in less than a minute......much less actually. S. Link to comment Share on other sites More sharing options...
wallyboss Posted March 4, 2010 Report Share Posted March 4, 2010 You don't have to mess the angle by much to render an auger useless. Link to comment Share on other sites More sharing options...
pike slayer Posted March 4, 2010 Report Share Posted March 4, 2010 WOW Link to comment Share on other sites More sharing options...
skinny Posted March 4, 2010 Author Report Share Posted March 4, 2010 is there a way to check the angle to see if this one is bent Link to comment Share on other sites More sharing options...
Spiel Posted March 4, 2010 Report Share Posted March 4, 2010 I posted this last year, might help.....? http://www.ofncommunity.com/forums/index.p...&hl=dremmel Once you're sure the blades are sharp try shimming them, you may need to play with shim thickness till you find just the right one. Link to comment Share on other sites More sharing options...
shane Posted March 4, 2010 Report Share Posted March 4, 2010 These auger threads are boring. HAHAHAHA! Get it?.....auger?......boring? C'mon spring. Link to comment Share on other sites More sharing options...
skinny Posted March 5, 2010 Author Report Share Posted March 5, 2010 well back to this boring question added is a picture of how the blades were on the auger I started to remove them then took the picture are they on in the right way Link to comment Share on other sites More sharing options...
irishfield Posted March 5, 2010 Report Share Posted March 5, 2010 I'd say they're on upside down... Link to comment Share on other sites More sharing options...
skinny Posted March 5, 2010 Author Report Share Posted March 5, 2010 can some one send a picture of what they are to look like Link to comment Share on other sites More sharing options...
glen Posted March 5, 2010 Report Share Posted March 5, 2010 Your blades are upside down. Take the blades off and flip them over. "can some one send a picture of what they are to look like" They look just like the ones you have but mine are not upside down. Link to comment Share on other sites More sharing options...
Big Cliff Posted March 5, 2010 Report Share Posted March 5, 2010 Just flip them over inside to out but, the flat side of the blade should be toward the ice. Judging from the amount of rust on them you should probably get a new set anyway, they are only $20.00 for the set. Link to comment Share on other sites More sharing options...
DRIFTER_016 Posted March 5, 2010 Report Share Posted March 5, 2010 (edited) I posted this last year, might help.....? http://www.ofncommunity.com/forums/index.p...&hl=dremmel Once you're sure the blades are sharp try shimming them, you may need to play with shim thickness till you find just the right one. Yeah they are upside down too. If you need to shim it. The shims go closer to the back of the blade (non cutting edge) as well to increase the cutting angle of the blade. Cut open a pop or beer can and cut strips to use as shims. Edited March 5, 2010 by DRIFTER_016 Link to comment Share on other sites More sharing options...
Sinker Posted March 6, 2010 Report Share Posted March 6, 2010 Yep, they're upside down for sure. They're not going to cut ice, even if you put them on right, you need new ones. Make sure you put them on with the flat side down. Watch your fingers, they're really sharp! S. Link to comment Share on other sites More sharing options...
skinny Posted March 6, 2010 Author Report Share Posted March 6, 2010 ok is this right Link to comment Share on other sites More sharing options...
Sinker Posted March 6, 2010 Report Share Posted March 6, 2010 I'm pretty sure they were right in the first pic, now that I look at the second pic. Its hard to tell from a picture. The flat side of the blades should be on the ice. Bud, you need new blades. Those are not going to cut ice. You can do anything you want, shim them, sharpen them, whatever, they aren't going to cut as good as new ones. For the $25 they cost, its worth it. Especially now with thick ice everywhere. They will last all next season no problem, as long as you take care of them, and don't bang them around. S. Link to comment Share on other sites More sharing options...
Spiel Posted March 6, 2010 Report Share Posted March 6, 2010 I have the same auger and I can assure you they were not upside down in the first picture, they are however upside down now. Link to comment Share on other sites More sharing options...
Spiel Posted March 6, 2010 Report Share Posted March 6, 2010 I'll add acouple more things here. First those blades definitely look to be in need of sharpening, if you do it yourself be sure to only sharpen from the top side off the blade, never the bottom. Shims need to be placed between the auger head and the blade on the cutting edge side of the bolts to steepen the angle of attack. Also note that the offset handle auger requires rotation with both arms as seen in this video. Hope this helps. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now