mattyk Posted July 4, 2015 Report Share Posted July 4, 2015 My shimano saros 2500 has started seizing up. I'm not sure what the problem is. I had this happen with a Diawa Lexa last year too. I tried using some reel oil and it helped a little bit but I'm still having issues with it. Any one experience this issue, how did you fix it? Thanks. Link to comment Share on other sites More sharing options...
FloatnFly Posted July 4, 2015 Report Share Posted July 4, 2015 get a new bearing or buy a new reel Link to comment Share on other sites More sharing options...
Gnote Posted July 4, 2015 Report Share Posted July 4, 2015 (edited) Did you take the whole reel apart to oil the bearings? My pflueger has been in the water 3 times but i took it apart piece by piece and oiled the bearings very well all the while spinning the handle to force dirt water and crap out of the working components. If you dont get right in there the oil wont do much. Take your time, lots of little pieces that can get mixed up. Hope this helps good luck. Edited July 4, 2015 by Gallie Link to comment Share on other sites More sharing options...
Fisherpete Posted July 4, 2015 Report Share Posted July 4, 2015 If you are close to them, Shimano in Peterborough does an amazing job tuning their reels, I think it is $25-30 for a Saros and that includes any parts that need replacing. My Calcuttas and Stradics come back like new after I take them in. Pete Link to comment Share on other sites More sharing options...
Moosebunk Posted July 5, 2015 Report Share Posted July 5, 2015 Had a Symetre do the same not that long ago. Took the reel apart and the big, rubber seal (see diagram part 11121) was worn and torn. It's basically there just to help keep some water but mostly dirt and debris out so I removed it, put all parts together again and the reel works great again. Only thing will be, I'll have to be more careful if dunking it and maybe clean it out a little more often. Check it out, could be the prob. Link to comment Share on other sites More sharing options...
mike rousseau Posted July 5, 2015 Report Share Posted July 5, 2015 Since this is the second reel I'm guessing there's a common denominator here... Do you leave your rods in the boats rod locker...? Mine had lots of moisture as they aren't sealed and was causing issues with my reels.... Link to comment Share on other sites More sharing options...
mattyk Posted July 5, 2015 Author Report Share Posted July 5, 2015 Thanks for all the replies. Will check out the diagram part MB. Mike I keep the reel indoors all year. But you make a good point. Link to comment Share on other sites More sharing options...
solopaddler Posted July 5, 2015 Report Share Posted July 5, 2015 Mine had lots of moisture as they aren't sealed and was causing issues with my reels.... This. If they get wet or damp, often they'll run rough until they comletely dry out. A re-greasing wouldn't hurt either. Link to comment Share on other sites More sharing options...
MCTFisher9120 Posted July 5, 2015 Report Share Posted July 5, 2015 Send it to Shimano in Peterborough. $25 and they will open up the reel, clean and service it as well as fix the problem and replace any parts that need replacing. It sounds like it might be the friction ring but can't be sure. I wouldn't take this out as it stops pre-mature bail trip, it locks the bail in so when you cast the bail doesn't fly down...they get warped or bend sometimes and this will slow down the reel. We can send it for you at Gagnons...if your close to Peterborough do it yourself it will save you the $10 in shipping. Link to comment Share on other sites More sharing options...
lew Posted July 5, 2015 Report Share Posted July 5, 2015 Send it to Shimano in Peterborough. $25 and they will open up the reel, clean and service it as well as fix the problem and replace any parts that need replacing I'm taking a Calcutta TE into Shimano tomorrow morning for an adjustment and cleaning. They do excellent work there, the pricing is great and the customer service is 2nd to none. Link to comment Share on other sites More sharing options...
chimpboy_to Posted July 6, 2015 Report Share Posted July 6, 2015 If you want to do it yourself, I followed the video here and my reels were like new. The supplies you can pick up most tackle stores. http://anglingauthority.com/shimano-spinning-reel-maintenance-tutorial/ Andrew Link to comment Share on other sites More sharing options...
Beans Posted July 6, 2015 Report Share Posted July 6, 2015 I had Shimano in P'Boro fix my Curado Batam...Seems whoever refurbished it (China) put the magnets in backwards ??? Link to comment Share on other sites More sharing options...
musky_hunter Posted July 6, 2015 Report Share Posted July 6, 2015 Send it in to Shimano for sure. I hate working on spinning reels, they have the proper rig to reinstall the reel properly and if 1 part fails i'm sure a few others will need to be replaced. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now