Nemo Posted August 19, 2009 Report Share Posted August 19, 2009 My wife is up at the cottage and is reporting a problem with the motor on the tinnie. Apparently she can get it to start but when she puts it into gear (forward or reverse) it stalls out. They checked/changed the gas and still an issue. I suspect it is an issue with the carb such as blockage of the valve with dirt. Any ideas on a quick fix or other causes to consider. Appreciate your thoughts. The motor is mid 90's 2 stroke 15hp. Cheers Nemo Link to comment Share on other sites More sharing options...
Bernie Posted August 19, 2009 Report Share Posted August 19, 2009 Seized gears in the lower unit? Only running on one cylinder? Link to comment Share on other sites More sharing options...
gone_fishin Posted August 19, 2009 Report Share Posted August 19, 2009 try running it with the choke out... my buddy had this problem earlier in the year, ran it with the choke out for a bit, then it seemed to work fine after that... the problem kinda fixed itself... not saying that will happen for you, but it's worth a try. Link to comment Share on other sites More sharing options...
danbo Posted August 19, 2009 Report Share Posted August 19, 2009 (edited) Buy her a nice Kayak.. Check for line around prop. Or pull the plugs to see if fouled. Check/replace the fuel filter. Bang the side of the carb for a stuck float. Call the local Marina. Edited August 19, 2009 by danbo Link to comment Share on other sites More sharing options...
NAW Posted August 19, 2009 Report Share Posted August 19, 2009 I have the same motor (89 merc), and have had the exact same issues in the past. For me, it was a plugged up carb that needed a good cleaning. For a potential quick fix, you can start the motor with the cover off. Manually throttle up the motor by pulling the throttle lever on the side of the carb. That way you can rev up the motor without it in gear. May clean out your carb a little. It's an easy thing to try. Link to comment Share on other sites More sharing options...
Jonny Posted August 20, 2009 Report Share Posted August 20, 2009 Bring some Seafoam with you when you go up there. Link to comment Share on other sites More sharing options...
bigfish1965 Posted August 20, 2009 Report Share Posted August 20, 2009 Bring some Seafoam with you when you go up there. That's the ticket.... Link to comment Share on other sites More sharing options...
Nemo Posted August 20, 2009 Author Report Share Posted August 20, 2009 THanks for the tips gentlemen. THe plug was pulled and it is pretty dirty so I am going to replace it and the filter and have the carb cleaned. BTW where is the best place to pick up some Seafoam. I googled CTC for it and it didn't show.... Appreciate all the advice. Nemo Link to comment Share on other sites More sharing options...
scugpg Posted August 20, 2009 Report Share Posted August 20, 2009 THanks for the tips gentlemen. THe plug was pulled and it is pretty dirty so I am going to replace it and the filter and have the carb cleaned. BTW where is the best place to pick up some Seafoam. I googled CTC for it and it didn't show.... Appreciate all the advice. Nemo NAPA Link to comment Share on other sites More sharing options...
Jonny Posted August 20, 2009 Report Share Posted August 20, 2009 Another source for Seafoam is Benson Auto Parts, if they have a store near you. Link to comment Share on other sites More sharing options...
Nemo Posted August 20, 2009 Author Report Share Posted August 20, 2009 Thanks again gents. Link to comment Share on other sites More sharing options...
Nemo Posted August 25, 2009 Author Report Share Posted August 25, 2009 Well it looks like it was the carb needle. Cleaned carb, replaced gear oil and spark plug. Total Cost $350 approx. Wow that hurts. Shop rate = $99 per hour. Most of it is time 2.5 hours. Is this reasonable for what was done? Your thoughts appreciated. Link to comment Share on other sites More sharing options...
danbo Posted August 25, 2009 Report Share Posted August 25, 2009 (edited) That's why they get the big bux! Sure beats rowing.. We all learned from your misfortune today. Edited August 25, 2009 by danbo Link to comment Share on other sites More sharing options...
Fisherman Posted August 25, 2009 Report Share Posted August 25, 2009 That's why I like Seafoam, preventive maintenance in a can. Link to comment Share on other sites More sharing options...
danbo Posted August 25, 2009 Report Share Posted August 25, 2009 Link to comment Share on other sites More sharing options...
Jonny Posted August 25, 2009 Report Share Posted August 25, 2009 Well it looks like it was the carb needle. Cleaned carb, replaced gear oil and spark plug. Total Cost $350 approx. Wow that hurts. Shop rate = $99 per hour. Most of it is time 2.5 hours. Is this reasonable for what was done? Your thoughts appreciated. I guess that depends if the carb was removed, disassembled and a new carb kit put in. Was that the case? If you left the motor at the service shop and they simply told you it was cleaned, they might have run Seafoam through it for you and little else? If a new carb kit was installed, the cost might be reasonable. The lower unit oil you could have replaced yourself very simply and in about 15 minutes (and had nothing to do with the motor problem, as I'm sure you're aware). Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now