Jump to content

FISH FINDER-EAGLE CUDA 168 (portable)


danbo

Recommended Posts

My friend has one, it works ok on ice as long as there isn't a flasher too close. He used his on Simcoe and worked fine. But when we were in a hut the next time and I brought my flasher, his sonar was useless. The flasher was horribly interfering with the sonar. Not sure how close you could have it to a flasher before it becomes affected.

Link to comment
Share on other sites

used mine all last season on the ice...works mint...You have to McGyver a bracket to keep the transduser planted or else you will never get a good reading ... The cold didn't affect it, but yes as stated above, " you can't be next to another finder within 10ft

Link to comment
Share on other sites

used mine all last season on the ice...works mint...You have to McGyver a bracket to keep the transduser planted or else you will never get a good reading ... The cold didn't affect it, but yes as stated above, " you can't be next to another finder within 10ft

 

 

Can you expand on your setup. Ive got this same unit and was wondering how to rig it for icefishing. I was thinking you could just toss a bit of weight on the transducer mount to hold it down?????

Link to comment
Share on other sites

Can you expand on your setup. Ive got this same unit and was wondering how to rig it for icefishing. I was thinking you could just toss a bit of weight on the transducer mount to hold it down?????

 

Jay, take the suction cup off the transducer and bolt it to a piece of wood (a 2' chunk of 1X2 works for me).

 

Bolt an 8 or 10" piece of wood at the top to brace across the top of the ice hole.

 

I usually tape the transducer cable to the wood with electrical tape to keep things neat.

Link to comment
Share on other sites

Jay, take the suction cup off the transducer and bolt it to a piece of wood (a 2' chunk of 1X2 works for me).

 

Bolt an 8 or 10" piece of wood at the top to brace across the top of the ice hole.

 

I usually tape the transducer cable to the wood with electrical tape to keep things neat.

 

 

Pretty much the same setup as what I have put together....I just mounted the transducer to a 30" piece of angle iron and mounted a 12" square piece of plywood to the top of it which a pack with snow on the side of the hole.. I found the angle iron worked well, because I could move the transducer down a few holes as the ice got thicker throughout the season...If the transducer is to far past the bottom of the ice , I found the current was causing it to sway to much and screwing up the reading... Wait till you throw down your first hand full of salties.. watching them sink , you will never believe how long they take to get down to 80ft of water :D

 

Its pretty piss poor but you get the idea

 

gallery_1414_562_1147.jpg

Edited by JDMLS
Link to comment
Share on other sites

2x2's or hockey sticks nailed or screwed together in "T" fashion. Duct tape the transducer to the bottom of the T and you are good to go. Sounds stupid but works fine and is easily made from materials lying around. Can be made in less than 5 mins.

 

Just make sure the transducer and the bracket are sitting level.

 

Portbolster08002.jpg

Edited by Riparian
Link to comment
Share on other sites

My friend has one, it works ok on ice as long as there isn't a flasher too close. He used his on Simcoe and worked fine. But when we were in a hut the next time and I brought my flasher, his sonar was useless. The flasher was horribly interfering with the sonar. Not sure how close you could have it to a flasher before it becomes affected.

 

Ya... its all fun and games until your friend brings a flasher to the hut that is equiped with "interference rejection" technology. :whistling:

Link to comment
Share on other sites

Hey danbo,

 

The Eagle Cuda is very similar to the Lowrance X67c....except its not colour and a few other things like the battery set up....but it accepts most of the accessories for the Lowrance X67c...including the stuff that turns it into an ice fishing" unit.

 

 

That is to say that ou can use a Lowrance "iceducer" Code PTI-WSU part#106-68 which is basically a self levelling transducer ( i bought one of these and use it now, but i did go the hockey stick method before hand and it worked great too, the hockey stick is just a bit cumbersome)

Link to comment
Share on other sites

Hey danbo,

 

The Eagle Cuda is very similar to the Lowrance X67c....except its not colour and a few other things like the battery set up....but it accepts most of the accessories for the Lowrance X67c...including the stuff that turns it into an ice fishing" unit.

That is to say that ou can use a Lowrance "iceducer" Code PTI-WSU part#106-68 which is basically a self levelling transducer ( i bought one of these and use it now, but i did go the hockey stick method before hand and it worked great too, the hockey stick is just a bit cumbersome)

 

Someone recommended this to me last year.... It's must work perfect , but for $90 hmmm ..... When you can make it work with some scraps found laying in the garage :dunno: ...I wuold rather put the $90 towards a better unit as the cuda is as low end as it gets..

Link to comment
Share on other sites

  • 1 month later...

any transducer will interfer with the ones around it at a certain distance away and certain depth of water. I run a 520C through a Universal trans. built into my troller, and I have a skipper for the X27 off the back......my cones are dialed in to 19 degrees......my boat is 17ft long, so the trans. are 17ft apart.....now.....

 

each cone spreads out at 19 degrees the work OK till I get out to 25-27 feet of water then the cones overlap causeing interference. If I am alone, I simply turn of the X27 and the problem goes away.....If I have a partner and we are drop shotting over 25ft, I have an ethernet connection so that I can run both screens off the same transducer, so both guys see the same thing so in 35plus ft, you can see both jigs or rigs working the bottom at the same time.

 

for the ice, you simply have to spread out so the cones don't interfer with each other, and make sure those cones are dialed in a tight as you can get them for better detail under your hole.

 

Cheers

 

RR

Link to comment
Share on other sites

Have the same ffinder and almost same solution as SoloP.

 

Took two stir sticks for paint. Bolted one to the transducer after removing the suction cup and used duct tape to tape the wire to the top part of the stick.

 

Then just slide the other stir stick between the wire and the vertical stick and just below the duct tape.

 

Stick in the hole and your good to go. When you're done just pull the horizontal stick out and that's it.

 

Took less than 2 minutes to set up.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recent Topics

    Popular Topics

    Upcoming Events

    No upcoming events found

×
×
  • Create New...