BITEME

hmmmmmmmm...........

You guys get all the good storms🤘

might be of some help there was no escape here indoor-air-filtration (1).pdf

Nice rig why the concern I can see many happy days on that ill say it again know the conditions around and it’s all good! get out there peter

That’s a good looking dog Bill!

The dynamic duo Ursa and Orion

had kind of the same setup except one of us use to get up on the bow until it planned out then roll off the side ......fun times

think you can send me the plans for that one??????

Hockey sticks, plywood, pulleys and clothes line cable mostly tiller control though a steering wheel and throttle control was a luxury that just wasn't always available.

Anybody remember the gold cup races at Bronte Beach it was a good day for a picnic always I spent many years terrorizing Bronte Creek and Harbour as a kid with a sea flea and a 15hp jonson http://images.halinet.on.ca/OakvilleImages/Images/BHS/002656626.jpg

10 for sticking the landing!

Really! You went there

Just an update he won best of show in Texas at the Hand made motorcycle show very cool and well deserved

Plastic toboggan great deer mover will slide over every thing

Do all the stuff mentioned. I don’t think you have a pooched motor get it back in the water couple hours running or what ever bring it in. Loosen the bottom plug let some fluid out honey is good creamed honey is bad while your at it change the plug(s) I think you'll be fine peter

Have you ever had this motor running??

Do beat yourself up poop happens and this didn’t happen this winter this is a previous owner thing not your fault at all live and learn if you go the jb route after doing seals scarf up the area good where you are laying it down wipe it with acetone let it dry and go to it you’ll be fine!! peter

I did notice that I though it was just crappy weld

One more thing and this may not be kosher for everyone and may not even be necessary when I put it all back together again I usually sneer a thin layer of gasket maker on the flat matting surfaces peace out peter

The video method is good I have taken seals out like that not going to lie taking it off is my preferred method I would suggest you go one set of screws higher and get access to the water pump and change that rubber impeller worse thing is to be out in the middle of your favourite lake and not pumping cooling water once you undo it it will drop a bit and hang on the shift linkage usually a coupler with 2 set screws loosen the lower and the lower unit will come away put it up on a bench and go to town you will see the housing for the impeller you can’t miss it troll some forums specific to your mortor first time is always painful and bloody take your time be patient use your cell for disassembly and reassembly the money you save buy a new toy for the boat and take pride in your new skill YOU CAN DO IT!!!!!! cheers peter

Video looks good just take time you can do it!!! cheers Peter

Yes we are talking about the seal at the prop and both fill screws upper and lower should have either o rings or crush washers

If you want to pay me to fly out from Nova Scotia I’ll come do it but in reality I will say again it’s easy to do and doesn’t take long I only did pressure tests on the rescue boat drives as of roof of repair( needs to be reliable)

Here is my take on this I have had lots of experience in this you had water during the boating season for sure it didn’t happen over the winter if it did stay emulsified over the winter you should be okay you said used it’s likely time I try to do the seal every two years religiously unless I see what your seeing going forward if you want to drain in the fall fine but replace the oil you drain don’t let them sit dry this is a quick fix without getting soaked by a dealer the prop seal is very easy to do in your driveway do this first and run the motor on the water for a week if it’s milky again you could have other issues and it could be higher up the drive if not your a champ you didn’t say how big your motor was not that it matters pretty much all the same on the drive end its easy you can do it cheers peter

That is very slick Chris truly cool!!!!