irishfield Posted January 16, 2015 Report Posted January 16, 2015 Sounds like yours is a 3HP Jiffy WD... they were all 24:1. The 43cc I have is 40 to 1 but I just use my 50:1 Stihl oil in it.
DRIFTER_016 Posted January 16, 2015 Report Posted January 16, 2015 I always use stabil in my gas equipment & only Shell V power gasoline (V power contains 0 ethanol). I was unaware that there is a "marine grade" stabilizer. Where do I purchase this stuff? My Jiffy auger manual specifies a 24:1 mix. Anybody else have these specs? Mr. Topwater - I strongly recommend you read the owner's thoroughly before operating it. Follow their instructions. If your new auger should fail, at least you have followed their procedures when (hopefully it's not necessary) it comes time for a warranty repair. My Strikemaster is 24:1 but I run Opti-2 @ 75:1 in it. I run the same mix in all of my 2 stroke engines. Outboards, chain saws, augers etc. I also use stabil in every can of gas as well as in my boats tank. Doesn't matter what grade of gas I use though as there is no corn juice in any fuel up in the great white North!!
Lunker Larry Posted January 17, 2015 Report Posted January 17, 2015 I always use stabil in my gas equipment & only Shell V power gasoline (V power contains 0 ethanol). I was unaware that there is a "marine grade" stabilizer. Where do I purchase this stuff? My Jiffy auger manual specifies a 24:1 mix. Anybody else have these specs? Mr. Topwater - I strongly recommend you read the owner's thoroughly before operating it. Follow their instructions. If your new auger should fail, at least you have followed their procedures when (hopefully it's not necessary) it comes time for a warranty repair. You can get it at Canadian Tire etc. It is blue and not red and states Marine Stabil as the brand name. There are others out there. The common red stabilizer maintains gas quality and octane when stored. The blue marine stabilizer does the same but also addresses the ethanol issues. I use it in all my motors with regular gas. Leave them full, never drain and have never had an issue. 75 4 stroke yammaha, 50 hp 4 stroke merc, chain saw, weed eater, lawnmowers, you name it.
35Wailin Posted January 20, 2015 Report Posted January 20, 2015 Mr Topwater, I have the same auger. This is the third season with it. Fuel stabilzer is good advice. Also, I keep mine in the shed all year, with a full tank in the off season. Be careful with it in the cold, the black plastic does not like bouncing around. I have several pieces that have cracked and fallen off. I was getting ready to go fishing tomorrow and noticed that the kill switch is now only held by the wires. I'll have to make a small metal bracket for it now. Also spare blades are good and carry them with you. I drilled a bunch of holes the first year. I wanted to move a line later, and punched a hole right onto a rock. I couldn't cut any more holes. I went to CTC on the way home and bought another set. I was able to sharpen the originals and keep them in my tackle bag as spares. I also drilled a second hole throught the shafts below to bolt that attached the auger to the motor and inserted a coupler pin. The bolt and allen key are with my spare blades. This modification makes it a lot easire to break it down and pack it at the end of the day with cold hands. http://answers.canadiantire.ca/answers/9045/product/0406509P/no-master-lock-coupler-latch-pin-questions-answers/questions.htm
Mr.Topwater! Posted January 20, 2015 Author Report Posted January 20, 2015 Hey, 35wailin,I wrapped the auger motor in an old piece of carpet before putting it on my smitty sled. Are the blades easy to sharpen? Thanks. Tomorrow, pike!
Mister G Posted January 20, 2015 Report Posted January 20, 2015 I agree with Brian, cordless drill is the way to go for most guys.
35Wailin Posted January 20, 2015 Report Posted January 20, 2015 I just used a fine file and tried to follow the factory angle. They are stainless steel, so not really easy to sharpen. I just use them as spares if I get out to the lake and find I can't cut anymore for whatever reason. I noticed today, that the plastic holding the kill switch has broken as well, so I have to fabricate a metal bracket for it. The rest of the plastic that broke was mostly cosmetic anyway, except for the kill switch piece.
Burtess Posted January 21, 2015 Report Posted January 21, 2015 (edited) I have the same auger and I run TruFuel 50:1 in it (I do not have any other 2 stroke toys). For me this is the easiest and safest way to fuel the thing. Mine, in the cold (-20C and lower) it likes a full throttle start which would indicate it is tuned too rich I suppose? Anyway it starts lol.... Burt Edited January 21, 2015 by Burtess
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now