Tybo

Make sure you hook them up parallel. If you hook them up in series you have 24 volt. When using multiple batteries. you must start with fresh batteries(new). For your batteries will only be as strong as you weakest. the weaker battery will draw from the other until they are at the same amperage. You can hook up multiple chargers if the batteries are fresh.

Any 80w90 gear oil will work.

The trolling charger system are for engine that have alternator. the alternator needs to be high out put. If you try with a stator system. It will take out the regulator and the stator.

He wired it to 12 volt. one battery. This is not a good. It will draw more from the one. decreasing the power in both. In mutable batts set up. Your batts are as strong as the weakest one.

I was once told, You can always tell the fastest guy. Fore he's the one thats all most out of control. In the boating world. The fastest boat is the guy how has perfect control. There is many different styles of deep vees. Eg: Donzi and cigarette hulls use to dominate off-shore racing. Reggie Fountain came out with a new hull design and He the one that figured he could get more air under the hull.Then it was his turn to dominate.(Reggie also pilot and work his throttles). But soon after this hull design wouldn't go any fast. Along came Stephen Steppe. He the one that that figured out that if you notch the hull. This would create a vortex giving the hull more lift.Hence the stepped hull. Which give a performance deep vees the high speeds. If you take the same design. Put it on a 45 foot 20 foot beam boat, you will get a very smooth ride. The two best hull designs on aluminum fishing boats are Lund's pro-v and the alumacraft trophy. Thees two hull try to give you the best of both worlds. The bow is a true deep vee where the Stern is some what a reverse chime for hole shot and a stable ride at top end.

The higher degree in dead raise,the further the bow travels down the boat. to allow for this high degree,you must deepen the hull before mid-ship to allow for the right degree of curvature. With this done now, using the trim and the right drive and throttle. In rough seas you will be able to get the hull level. Which then the lowest part of the bow will strike the wave at tremendous force. Going to use physics here.Send the bow up and a smooth flow of water down the Stearn. Now this is where chimes come in.They prevent the stern from slipping.At the rear of the boat you will find a power plate at the end of the hull. This a flat at the end of the keel to counter-react the the bow lift. Now you have the throttles and the trims working great. The boat is preforming how it should. spending more time in the air then the water. Most aluminum fishing boats use a reverse chime hull to make it stable. Like I said, apples to kumquats.

Need some input. Don't want to get burnt. Also need a estimated transport cost. Oh. Talking about bring a boat up from the states.

Oh,man. have you just done a grave-mistake.

One of the fastest boats I've been in,was a aluminum deep V off-shore.130mph. This boat weighs more then Kevlar,with the weight being almost the same as glass. This is do to the heavy reenforcement of the bow. With this boat having a 26 degree dead raise the bow take more of a pounding then the average 17 to 19 of a aluminum fishing boat. The dead raise of the bow has more to ride stability the the material that the boat is made of. A long dead raise is made to ride on top of the water. A low dead raise will plow through the wave more. To truly under stand dead raising, go out in a sail boat. Then compare it to your fishing boat. You will under stand what I'm talking about. if the boats you are comparing have different dead raise. It would be like comparing apples to cumquat's.

Dawg, You stay on the shine. They won't need too embalm you.

Hey Wayne. Did some one forget to pre-heat.

If the dent and/or rivet doesn't leak. It doesn't need to be fixed.

Congrats again Brian and Betty. I thinks I've finally have recovered. Thanks again had a great time.

I'm a 99.8% solder type of guy.But since I found shrinkable butt connectors and liquid tape. A proffered repair for in-closed wiring has been this way. Use alot of in-cast multi wire on the proxies systems.Just over a mile. And on a .oo9 draw the butt takes .0003 of a amp. If the wire is in a harness or suspended always solder. Not a big fan of crushing twisting or too much heat on copper strand cable. But done right it will work. No mader which way it goes.

DO FORGET TRAILER TIRES NEED TO BE PUT ON.

I seen countless times where a solder join has worn through and create a short wear the join is in metal tubing. A shrink tube style of butt connector with liquid tape is a damn good repair in this case.

I don't let a salespersons talk to me. I do all my own research. I take my time When I make a big purchase. Took 2 years to buy my truck. I got the truck I wanted. Been buying a boat for a year. Have 4 salesmen rapped around my finger. When it's my money. I am the boss. In my opinion. Lund, Allumicraft. princecraft polarcraft mirrorcraft crestliner smokecraft sylvan crestliner

Sounds to me they followed the gun and found pot.

Use a butt connector.

. Was up in the man lift all day working on a rtg. At one time, their was golf ball side sleet. The man lift swinging. . East wind to top it off. So how was every bodies day.

If you like to have apiece of mine,while your driving. And don't mind spending some money. Tranny cooler. oil cooler. ceramic brakes. coil over shocks in the back. Use mid grade gas. A little expensive. But be able to tow\STOP,STOP,STOP, a 20 footer.

Tread Roll occurs when the tire gets to hot. The rubber becomes softer and then the tread is push over. You will know when this is happening, When you look at the tread and their is high spots on one side, Or a high ridge.

Highway car. pretty good. City car. Don't know any one that had good luck. Exploder.

I agree with Dan. The only true solution is too shut fishing down! Help in the efforts of habitat, then leave them alone.

I always go the most ply the wallet allows. This is not for weight.But for temperature. I like to call it super cruise. The fastest I can go,With the best fuel. When over rating your tires,You must adjust your pressures. Or you will get tread roll.