Guest LivingLegend Posted April 6, 2011 Report Posted April 6, 2011 (edited) I was going through my manual for the Curado 201E7 to keep it maintained properly yet it shows no diagram on where i should apply the lubricant drops. If anyone can show me a diagram or picture where exactly to apply this i would appreciate it greatly. There are lots of warnings not to lub to much and areas that could affect the functionality. Thanx. Edited April 6, 2011 by LivingLegend
Garry2Rs Posted April 6, 2011 Report Posted April 6, 2011 Unless you have dunked the reel you should only need a drop of oil on each of the three bearings on the spool shaft. There is one bearing on each side of the spool and another under the tension knob that is under the crank handle. If you have some lighter fluid you can wash the bearings out first and de-grease the centrifugal brake drum. If you don't have any don't worry, just oil the bearings.
Guest LivingLegend Posted April 6, 2011 Report Posted April 6, 2011 Unless you have dunked the reel you should only need a drop of oil on each of the three bearings on the spool shaft. There is one bearing on each side of the spool and another under the tension knob that is under the crank handle. If you have some lighter fluid you can wash the bearings out first and de-grease the centrifugal brake drum. If you don't have any don't worry, just oil the bearings. That sounds good. I havent submerged it under water (yet) so I will check out these three bearings. thanx for the tip!
wallyboss Posted April 6, 2011 Report Posted April 6, 2011 Videos on Youtube shows everything start with #1
Garry2Rs Posted April 7, 2011 Report Posted April 7, 2011 Ouch! personally, I wouldn't tackle a full tear down like that! If you need to open-up the gear box, I think it's time to take that puppy back to Shimano.
Rombo Posted April 7, 2011 Report Posted April 7, 2011 It a bad time of year to send it in. But i just bought my second curado and was talking with the shimano rep. He informed me you can send you reels to shimano in peterborough, they will go through the entire reel for around $20. I will be sending mine in next winter.
MCTFisher9120 Posted April 7, 2011 Report Posted April 7, 2011 Ouch! personally, I wouldn't tackle a full tear down like that! If you need to open-up the gear box, I think it's time to take that puppy back to Shimano. It's a easy process. I basically played the first Shimano video over a few times then the 2nd,3rd etc...after watching it i had it ready for reference then did a full service to my curado, i put a piece in wrong a few times but finally got it...not that many parts to confuse you in these reels...now a spinning reel is a different story...no where where to start on those
Guest LivingLegend Posted April 7, 2011 Report Posted April 7, 2011 Well I just picked up my Curado last year so not sure the full break down is needed. Just gonna give her alittle lubage yet for the future i will refer to those vidoes and save myself some cash that can go towards more tackle!! Thanx guys!
esoxansteel Posted April 9, 2011 Report Posted April 9, 2011 It a bad time of year to send it in. But i just bought my second curado and was talking with the shimano rep. He informed me you can send you reels to shimano in peterborough, they will go through the entire reel for around $20. I will be sending mine in next winter. Bud who fixed and maintained reels for shimano for years, and could service them with his eyes closed, I know I seen him do it has left shimano unfortunately
Spiel Posted April 9, 2011 Report Posted April 9, 2011 With an ounce of common sense, the appropriate schematics (in the box or online) and a set of assorted small left and right hand screw drivers you can clean, repair and lube 'em yourself.
Jer Posted April 10, 2011 Report Posted April 10, 2011 Bud who fixed and maintained reels for shimano for years, and could service them with his eyes closed, I know I seen him do it has left shimano unfortunately That's too bad. When did he leave? Is he still gonna work independently? Nobody could whip a reel back into shape like Bud could, most times at negligible cost.
ah_long Posted April 10, 2011 Report Posted April 10, 2011 it's always suggested that you take the reel out and re-grease/oil the reeel when you first got it, the bearings are always packed with grease and by doing your own lubing, you can greatly improve the performance on your reels.. and of course, you can upgrade the drag/bearings while you're at it, all my reels get the Carbontex drag upgrade with the exception of the Zillion Type R that has it already
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now