DRIFTER_016

You mean the Libtards that go out to protest an oil drilling rig in their kayaks made from dino juice?

http://blog.westjet.com/thoughts-evacuating-people-pets-from-fort-mcmurray/?sm_cid=social:ws-world:fort-mcmurray-forest-fires:all-channels

LOL

I said they weren't cheap!!!

I have nothing bad to say about the CT batteries. I run them on my boat. However if you have the $$$$ a LiOn battery would be the way to go. Much lighter but a lot more $$$. http://www.lithiumion-batteries.com/lithium-marine-batteries.php

https://www.thestar.com/news/canada/2016/05/10/calgary-pilot-breaks-rules-flies-displaced-fort-mcmurray-animals-to-shelters.html

Try Canadian Tire. http://www.canadiantire.ca/en/pdp/hillman-rubber-grommets-1612746p.html#.VzFG4fkrKM8 Napa or electrical supply houses would be a couple of other places to try.

Meh, it's just a little something I cobbled together to hold my lures. If you want to see something that took me a little longer and was a tad more difficult look at these pics.

In order to get a full charge you are going to need a pretty sizable panel or a pair of panels plus a charge controller. For instance a this 80 watt system only puts out a maximum of 4.6 amps in full sun. You really want at least twice and even better 3 times that output in order to get a good charge. The charge controller is like the battery charger you plug in at home. It regulates the amount of charge going to the battery so as not to over or under charge it. You would be better off with a 1000 watt generator and charger.

Those would be auger bits. If you are going to try pre-drill a pilot hole the size of the widest point on the screw tip so it doesn't draw the flutes into the metal. You want to go slow and with light pressure. Spade bits actually work pretty good in aluminium as the points on the tips of the wings cut through without chewing up the metal. But as I said with either type of bit the key is light pressure and low RPM.

If you mean a spade bit like in the pic below. It will work as long as it's one of the ones with the points on the end. It will wear out quickly and you need to go slowly, but it will work in a pinch. I use either a hole saw or UNI bit when I need to run stuff in my boat.

If you need to replace the rotors look into EBC brake parts. Good quality stuff. http://ebcbrakes.com/automotive-products/

Go see Tom @ Angling Specialties.

I had no idea Johnny had that kind of $$$$. You would never know it talking and fishing with him. ​One of the nicest most down to earth people I have ever met. Cool cave too.

Check your live well drain lines. It's possible one has a crack is allowing water to enter the bilge. I had a missing rivet in my aluminium boat and after a full day on the water I had the kind of water you are talking about. That was through one 3/16" hole.

I made a plywood box with sheet aluminum dividers with notches cut for the hooks to hang in.

Some pretty nasty images from Ft. Mac Not much left of this guys snowmobile. Here's a bunch more pics.

It's actually the entry to my place. It's 10'X10' but most of the room is taken up with a 500 gallon water tank. So, yeah it's tiny.

Yep, me too. Got 5 batteries sitting on the floor in my tiny shop. 1 for my camper, 1 for a buddies boat and 3 for my boat. Just finishing cleaning up after the tool box debacle of last week, then they go on the smart charger before I put them in the boat for the summer.

Yup, toasted a couple of batteries because the charger didn't shut off. The battery in my snowmobile is 9 years old now. It has a Battery Tender charger installed on it as well as a battery blanket and block heater. I plug in the night before I want to use it and it starts up like it's 70 degrees outside every time. I haven't even seen the battery in this sled as it's buried under a bunch of stuff. Probably see it tomorrow when I start taking it apart to get the rad out.

It depends!!! If you are getting work done by someone other than the dealer (this includes oil changes) make sure you have receipts and documentation. A friend here in YK had Subaru's for he and his wife. There is no dealer here in town so they had other shops do the work. Well both vehicles had expensive repairs needed under warranty and Subaru denied them since they didn't service the vehicle. I have my Honda Pilot and it is now out of warranty but I needed to replace a cracked rad under warranty. I called them up, told them about the issue, sent them pics of the area where it was leaking. They sent me a replacement and said I can get it fixed by the shop of my choice. I told them I was my shop of choice and was it OK to do the repairs myself. They said no problem. Moral of the story, contact the manufacturer and ask some questions. Take down the info of the person you talked to and the date of the conversation. Better yet confirm with an email and then print it out and put it in your vehicle file.

Well the winds have shifted and we are starting to get Ft. Mac's smoke here in Yellowknife.

Yep!!!

One of our water bombers and a spotter plane are down there and the rest of the fleet ready if requested. The govt also gave $50,000 to the red cross. http://www.cbc.ca/news/canada/north/nwt-water-bombers-fort-mcmurray-1.3570887