Kingsalmon Posted March 11, 2010 Report Posted March 11, 2010 Maybe somebody can help me with my question. I have an islander that is six months old and I changed the bearings to ABEC 7's. The reel spins almost forever if I Don't put the retaining screw in. Once I put the screw in and tighten, it seems that the rubber o ring is rubbing against the bearing and slowing it down considerably. Does anyone know if this is common. I know that this has been evident with my Islander since the first day as I thought it was the bearings, but it obviously was not. Thanks for the help. Mike
canadian_copper Posted March 11, 2010 Report Posted March 11, 2010 SHOULD OF CONTACTED ISLANDER FIRST BEFORE YA CHANGED THEM IF THERE WAS A PROB. 6MONTHS FOR AN ISLANDER IS NOTHING EVEN IF YOUVE USED IT EVERY DAY LOL NOW THAT U HAVE CHANGED THE BEARING U HAVE NO WARRENTY. SORRY CANT HELP THE OTHER PROB. NO IDEAS
solopaddler Posted March 11, 2010 Report Posted March 11, 2010 No worries that's a problem inherent with every single Islander and many other float reels as well. Fortunately it's a very easy fix. The problem as you mentioned, if you crank down on the screw the reel doesn't spin as well. If you back off on the screw a bit to get the reel spinning properly you run the risk of having your screw fall out on the river. Here's what you do: Wrap a tiny chunk of 4lb mono around the screw then screw it in to the point where you want it. Any small tag ends of mono sticking out can be trimmed. The mono holds the screw in place and is much easier than using something like loctight.
Spiel Posted March 11, 2010 Report Posted March 11, 2010 That's some good advice Mike and can be done while on the water if needed. I have the same issue with my Stanton which I solved by just rubbing down the threads with some sticky bees wax. Tighten down the retaining nut then back off a 1/4 turn or so.
ironstone74 Posted March 11, 2010 Report Posted March 11, 2010 Maybe somebody can help me with my question. I have an islander that is six months old and I changed the bearings to ABEC 7's. The reel spins almost forever if I Don't put the retaining screw in. Once I put the screw in and tighten, it seems that the rubber o ring is rubbing against the bearing and slowing it down considerably. Does anyone know if this is common. I know that this has been evident with my Islander since the first day as I thought it was the bearings, but it obviously was not. Thanks for the help. Mike You should be getting those machining jobs done instead of playing around with your toys there big man!!! Paul
Kingsalmon Posted March 12, 2010 Author Report Posted March 12, 2010 Thanks for the replies guys. As for replacing the bearings, the problem was there before I replaced the bearings so I thought changing the bearings might help. When I changed them, it was the same. And I'm not worried about the warranty as if I really wanted to, I could make my own reel in a few days that would rival any Islander out there. Just never have enough time in this point in my life. If its not busy at work, its busy with the 4 kids. No worries that's a problem inherent with every single Islander and many other float reels as well.Fortunately it's a very easy fix. The problem as you mentioned, if you crank down on the screw the reel doesn't spin as well. If you back off on the screw a bit to get the reel spinning properly you run the risk of having your screw fall out on the river. Here's what you do: Wrap a tiny chunk of 4lb mono around the screw then screw it in to the point where you want it. Any small tag ends of mono sticking out can be trimmed. The mono holds the screw in place and is much easier than using something like loctight. Thanks Solo. I'll try the line trick tonight. Without the screw in, it spins for a good 90 seconds before stopping. Put the screw in, it stops in 20 seconds. You should be getting those machining jobs done instead of playing around with your toys there big man!!! Paul Machining jobs? I could always use more as nothing is steady. Just super busy for two weeks then wondering if we should close the doors the next two weeks. As always the busy time always hits during the best fishing times, but I'm not complaining. Hopefully we'll get out soon so that I can smoke you with my new bearinged Islander. hahaha
ironstone74 Posted March 12, 2010 Report Posted March 12, 2010 (edited) Machining jobs? I could always use more as nothing is steady. Just super busy for two weeks then wondering if we should close the doors the next two weeks. As always the busy time always hits during the best fishing times, but I'm not complaining. Hopefully we'll get out soon so that I can smoke you with my new bearinged Islander. hahaha Talk's cheap, get to the river and we'll see !!! Paul Edited March 12, 2010 by Ironstone74
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now